Part 1

Condition survey – refurbishment in the last 5 years - KBCN1522

Where an asset has been refurbished, refurbished elements listed in criterion 2 can be excluded from the condition survey if:

The refurbishment was carried out less than 5 years ago.
The refurbishment addressed any and all major defects with the element.
The records of the refurbishment allow asset management to effectively maintain that element.

The intent of Rsc 01 is to give asset management a complete understanding of the condition of the asset. The requirement for 5 years is to make sure that this information is relatively up-to-date, and allows effective maintenance of the asset and management of any minor defects. All example scenarios below assume that the refurbishment was carried out less than 5 years ago. Any refurbishment works carried out more than 5 years ago must follow the full criteria of this issue. [accordion] [accordion_block title="Scenario 1"] A major refurbishment to a Commercial asset covered and effectively documented refurbishment to: a. Structure. b. Mechanical components. c. Electrical components. d. Plumbing. e. Fire protection. It did not cover: f. Communications and life safety systems. g. Health and safety conditions. All major defects were resolved. Credits for the condition survey, and for rectifying defects are awarded based on elements f. and g. only. [/accordion_block][accordion_block title="Scenario 2"] A major refurbishment has covered and documented all items in criterion 2. All major defects were resolved, but there are some outstanding minor defects that are being monitored and maintained by asset management. BIU V6: This issue is filtered out as per criterion 1. BIU 2015: The relevant credits are awarded. Minor defects are common after major building or refurbishment works, and typical building contracts provide a period for the resolution of minor defects. As long as major defects are resolved by the refurbishment, and asset management are aware of and managing minor defects, these items can be excluded from the condition survey. [/accordion_block][accordion_block title="Scenario 3"] A major refurbishment covered all elements, but there is no record of the refurbishment of mechanical and electrical components. A condition survey covering these items is required. Relevant credits are awarded for surveying and addressing any defects for these elements. [/accordion_block] [/accordion]

Converting water consumption into litres per year from new EU energy labels - KBCN1548

The following conversion factors may be used to convert the water consumption on new EU energy labels from litres per cycle (L/cycle) into litres per year (L/year): Dishwasher: multiply water consumption figure on EU energy label by 280 (to go from L/cycle to L/year). Washing machines: multiply water consumption figure on EU energy label by 220 (to go from L/cycle to L/year). This follows equivalent guidance for converting energy consumption (see KBCN1462).

25 Aug 2023 - Correction to 'typo error' for dishwasher conversion factor - previously shown as 208, now corrected to 280.

District heating / cooling / hot water – entering data into the Online Platform - KBCN1536

For assets which use district heating / cooling / hot water, information on the district systems are entered into Ene 09a and 09b. In Ene 05 / 06 / 09, answer 'no' to first question "Is space heating / cooling / hot water generated on-site?" then navigate to:

Ene 09a to answer questions on district cooling.
Ene 09b to answer questions on district heating and hot water. A district heat network will also provide hot water, so information on the system which provides both is entered into Ene 09b.

The Online Platform differs from the manual structure, however it does not affect scoring in any way. All data entered contributes to the asset energy calculator. Assets with on-site and off-site systems Only answer questions on the system which provides the most signifcant heating or cooling to the asset. If an asset includes both on-site and off-site systems, choose the one which delivers the most energy annually.

Emergency lighting - KBCN0185

Maintained systems featuring emergency light fittings which are also used for normal operation, are assessed for this issue. Non-maintained lighting which is only activated in an emergency can be excluded from the assessment. NC / RFO / BIU V6 Ene 17: The aim of these credit(s) is to encourage and recognise energy-efficient fittings. Non-maintained emergency lighting will very rarely be activated and in such extremes the emergency requirements must not be compromised. BIU V6 Hea 05: Flicker is eliminated from maintained systems only.

24-Jan-2024 - Scheme applicability updated to include BIU V6.

Enhanced waste collection in the asset - KBCN1528

Where the asset collects 6 or more unique residential waste streams on-site, answers G and H are available without the need for additional off-site collection points. If the asset can provide enhanced waste collection and sorting on-site, then this is effectively the same as having a compliant collection point in the local area. Example scenarios [accordion] [accordion_block title="5 waste streams on-site"] An apartment building has compliant facilities or kerb-side collection for 5 residential waste streams. There is no collection for composting or garden waste. The asset achieves the requirements for answer C only if all relevant criteria are met. There aren't enough waste streams to meet the threshold for answer G. [/accordion_block] [accordion_block title="7 waste streams on-site"] An apartment building has compliant facilities or kerb-side collection for 7 residential waste streams. There is no collection for composting or garden waste. The asset achieves the requirements for answer C, and answer G if all relevant criteria are met. [/accordion_block] [accordion_block title="7 waste streams on-site, with off-site collection point within 500m"] An apartment building has compliant facilities or kerb-side collection for 7 residential waste streams. There is no collection for composting or garden waste. An off-site collection point within a compliant distance can collect 5 waste streams, however only 2 are unique (different from what the asset already collects on-site). In total there are 9 unique waste streams collected on-site, kerb-side, or within a compliant distance. The asset achieves the requirements for answer C, and answer H if all relevant criteria are met. [/accordion_block] [/accordion]

Erratum – scope of issue - KBCN1498

Criterion 1 states: "Where external lighting or car park lighting are not necessary from a safety perspective, the associated credits can be filtered out of the assessment." What this means is:

Where external lighting does not exist, filter out the relevant credits.
Where car park lighting does not exist, filter out the relevant credits.
Whether or not the lighting exists for safety reasons has no effect on credit filtering.

The inclusion of the word 'safety' in this criteria is misleading and will be removed in future versions.

28-Feb-2024 - Wording clarified.

Erratum – up to V6 – methodology – no default energy assumptions - KBCN1630

The scope of the issue applies only to systems with significant energy use. The methodology section states that the online platform will calculate default values, and use this to indicate which systems are in scope. This is incorrect, as default values are not automatically calculated. The energy use of each system will need to be manually estimated. This can be done based on:

Typical benchmark values, and / or,
Estimates based on the capacity of equipment, and annual equivalent full load hours of use.

Erratum – up to V6.0.0 – Ecological features – Answer D – planters - KBCN1543

Outdoor planters and traditional planted areas can be considered as one feature for the purposes of Answer D, provided there is enough planting on the site to meet the intent of the issue. To meet the requirements of Answer D, the following must be demonstrated:

Outdoor planters, containing live plants and/or traditional planted areas
Other planted areas such as green roofs or green walls
Features to assist local fauna

20-Dec-2023 – The intent of this KBCN was to simplify compliance with Answer D. This has now been updated to clarify that it only applies to Answer D, thereby removing the potentially negative impact on meeting the requirements of Answer C.
24-Aug-2023 - Wording clarified. Change will be updated in the next re-issue of the manual.

Erratum – up to V6.0.0 – compliant cycle storage - KBCN1595

Criteria Instead of answer C, criterion 3 should refer to answers D and E. Evidence The criteria references for this issue are incorrect, and will be corrected in the next re-issue. Checklists and tables

Answer D awards 2 credits for achieving the minimum number of cycle storage.
Answer E awards 1 additional credit for achieving additional cycle storage.

The headings in Table 20 do not match these answers. Table 20 will be revised with these updated headings:

Home size	Answer D Minimum cycle storage 2 credits	Answer E Additional cycle storage +1 additional credit
Studio or 1 bedroom	1 cycle space / 2 homes	1 cycle space / home
2 - 3 bedrooms	1 cycle space / home	2 cycle spaces / home
4+ bedrooms	2 cycle spaces / home	4 cycle spaces / home

Erratum – V6.0.0 – cooling efficiency parameter – EER / SEER - KBCN1560

In the asset energy calculator guidance, the parameter given for cooling efficiency is 'SEER' (Seasonal Energy Efficiency Ratio). This is incorrect and should say 'EER'.

This affects the following tables:

	International	USA
Commercial V6.0.0	Table 19	Table 18
Residential V6.0.0	Table 16	Table 16

This will be updated in the next manual re-issue.

Evidence of no risk – Use of Approved Standards and Weightings List - KBCN0959

The current BREEAM International Non-Domestic New Construction Approved Standards and Weightings List (ASWL) can be used as evidence to demonstrate that a country has ‘no risk’ to all natural hazards apart from flooding (which is considered within POL 02 of BREEAM In-Use 2015 and Rsl 01 of BREEAM In-Use Version 6). Any country which has a weighting of 0% for Hazards within the current ASWL can provide this to BRE Global as evidence. As flooding is not included within the Hazard section of the ASWL, it must be evidenced separately. Therefore, in order to achieve maximum credits within MAT 05 or Rsl 03, the assessment must also provide evidence that the asset is in a ‘low or zero flood risk area’ under the requirements of POL 02 (BREEAM In-Use 2015) or Rsl 01 (BREEAM In-Use Version 6). Note: BREEAM In-Use International Assessors who are not BREEAM International Non-Domestic New Construction Assessors, will be unable to access the ASWL. In this instance please send a technical query to BRE Global outlining the country which the asset is located, and BRE Global can confirm the current weighting for that country. This KBCN does not apply to BIU assessments under BREEAM NOR or BREEAM SE

29-Nov-2023 Clarification - N/A BREEAM NOR/SE 
01-Oct-2022 Updated to apply to BREEAM In-Use Version 6
16-Aug-2016 Amended to clarify situations where there is no access to the ASWL

Flood risk – use of flood maps only in FRA - KBCN1524

Answer option E (Commercial) or F (Residential) If a flood risk assessment considers flooding from rivers and seas only, flood risk is zero / low, and the following requirements are met:

There are local or national flood maps available covering these sources of flooding.
The maps are accurate, up to date, and have sufficient detail to clearly identify flood risk for the asset.
The maps are approved by local or national government, and based on robust data.

It is acceptable for the flood risk assessment to be carried out by a relevant member of the team. It does not require a competent individual (see manual definition) to do this. Most sources of flooding are site-specific and require specialist input and calculation to quantify. However, flood maps meeting the criteria above can provide an acceptable level of assurance of overall flood risk from rivers or seas without the need to engage a specialist. Answer option C Where the risk of flooding is medium or high, flood mitigation measures are required (criterion 3). These mitigation measures must be defined by either:

A local authority (the measures must be relevant to the asset).
Or a competent individual.

The FRA can still be produced by a relevant member of the team. Exemplary credit This option is only available if a site-specific FRA was carried out by a competent individual, and cannot be based only on flood maps that give an allowance for climate change. Example scenarios [accordion] [accordion_block title="Low / zero flood risk"] National flood maps cover flooding from rivers and seas. The flood risk from these sources is zero / low. The compliant FRA can be produced by a relevant member of the team. [/accordion_block] [accordion_block title="Medium / high flood risk"] National flood maps cover flooding from rivers and seas. The flood risk from these sources is medium / high. Flood mitigation measures are required. The local authority provides some general flood mitigation measures for the area, but these are not relevant to the assessed asset. Instead, a competent individual is consulted on relevant flood mitigation measures for the asset - their recommendations are recorded in the FRA. The compliant FRA can be produced by a relevant member of the team. [/accordion_block] [/accordion]

Interlock controls – clarification - KBCN1491

An interlock is a control that is wired so that when there is no demand for heating / cooling in a space, the heating / cooling generator and the associated pumps are switched off. Use of thermostatic radiator valves (TRVs) alone does not provide interlock. Partial interlock means that the cooling and heating interlock controls are separate. However, the control function may be set up to minimise the possibility of simultaneous heating and cooling. Total interlock means the controls are wired so that simultaneous heating and cooling is not possible. Where there are separate local heating or cooling units present, these will also need to be wired into the control system for total interlock to avoid the possibility of simultaneous heating and cooling.

Intruder alarm systems – apartment buildings or similar - KBCN1572

Scope The scope of this KBCN applies to any residential asset that:

Is comprised of multiple self-contained dwellings within a single building envelope, and
Share common entrance(s) and circulation.

A typical example is an apartment building. Principle The asset as a whole is protected by systems that are fit for purpose to ensure the safety and security of the asset, its users and their property Implementation Security requirements for apartment buildings will vary greatly depending on factors such as:

Scale and configuration.
Access strategy.
Local context.
Which areas are under building management control.

Because of this, BREEAM cannot provide specific guidance on how intruder alarms and access control are configured to meet the principle. It is the role of the assessor and a competent third party (for instance, this can be a 'competent person' as defined in Rsl 10) to evidence how this principle is achieved for the asset as a whole. Evidence from a compliant security risk assessment carried out in line with Rsl 10 can be used to support this issue. Management-based solutions As a Part 1 issue, this intent must be achieved by systems which are intrinsic to the asset. Management-based solutions (such as a concierge service, or security guards) cannot be used to achieve answer E (intruder alarm systems). Answer F (alarm receiving centre) can only be achieved with a system that complies with Answer E.

Intruder alarms – Requirement for these to be audible when activated - KBCN1597

Where it is justified by the security consultant, project team or building management that a 'silent' intruder alarm system is more suited to the asset’s overall security strategy, this can be considered as meeting the Definition in our guidance.

Minimising flicker – scope of issue - KBCN1639

Principle Flicker from all lighting systems is eliminated. This means eliminating flicker in:

All lighting within management control, common areas, and tenanted areas.
Occupied, un-occupied and external spaces.

Only emergency lighting is excluded. See KBCN0185. Lighting flicker is undesirable regardless of location or length of exposure. Commercial scope Eliminate flicker in all lighting. Residential scope Eliminate flicker in:

All communal areas (internal and external, occupied and unoccupied).
Management offices, and all areas under management control.

Minimising watercourse pollution – Areas to be assessed - KBCN1633

Criterion 2 should be interpreted as follows: The intent is to provide a list of areas that are likely to present a risk of watercourse pollution. All the listed areas must be considered, however, where a listed area is not present, or it is present but poses no risk of watercourse pollution, this should be justified with supporting evidence. Where the development does not include any of the listed areas, or none of the areas present poses a risk of watercourse pollution, justification and evidence must be provided and this issue should be filtered out, in line with Criterion 1.

Occupant control – spaces requiring user controls - KBCN0170

This guidance is intended to clarify the types of area for which user controls are required or would be considered beneficial. Zoning is required in all areas of the asset where specified in the assessment criteria. Please refer to the specific requirements of the applicable BREEAM standard to interpret this guidance appropriately. User controls required Spaces where users are expected to have independent control over their environment.

Owned spaces: small rooms for a few people. For instance, cellular offices, owned spaces in residential assets.
Temporarily owned spaces: where occupants expect to operate the environmental controls while they are there. For instance, meeting rooms and hotel bedrooms.
Shared spaces. For instance, multi-occupied areas such as open-plan offices or workshops.

User controls not required Spaces where users are not expected to have independent control over their environment.

Managed spaces: where environmental control is expected to be centrally managed. For instance, atria, circulation areas, concourses, entrance halls, function halls, restaurants, libraries, and shops.
Occasionally visited spaces. For instance, storerooms, bookstacks in libraries, aisles of warehouses, toilets.

14-Dec-2022 - KBCN applicability updated to include BIU. Wording clarified, and amended for compatibility with BIU criteria.

On-site LZC – whole site shared connection - KBCN1424

To be recognised in BREEAM, the on-site Low and Zero Carbon (LZC) technology must have a direct physical connection to the assessed asset. OR Where the LZC technology is;

Located on the same site,
Is owned and managed by the same organization as the assessed building, and
Where it is impractical to physically connect the assessed building to the system,

It is acceptable to allocate the renewable energy generated proportionally as a calculation of the asset's predicted energy consumption compared to the total energy consumption of the whole site. To allocate renewable electricity by proportional consumption:

Obtain the total annual renewable electricity generated on-site.
Exclude all renewable electricity which has been exported to the grid.
Determine the respective electricity consumption of all assets on the whole site (predicted for new builds and measured for existing assets).

Where consumption data is missing, renewable electricity must not be allocated to the assessed asset. In this case, it is assumed that all electricity consumed is sourced from the grid.

17-Jan-2024 - Applicability BIU V6 Ene 13 removed, as this approach is not applicable to assessing the area of PV fitted.
21-Dec-2022 - Applicability to In-Use V6 confirmed.
24-Aug-2022 - Applicability to UKNC V6 confirmed.

Risk assessment – flooding is the only natural hazard - KBCN1552

Where:

Flooding is the only natural hazard identified and,
The flood risk assessment (FRA) from Rsl 01 is used as evidence for this issue,

then Answer D ('the asset is in an area where no risks exist') is only available where the FRA shows zero or low flood risk from all sources of flooding. Assessing flood risk from rivers and seas only does not cover all risks.

Safe pedestrian routes: definition, measurement and verification - KBCN0238

Definition Safe pedestrian routes include pavements and safe crossing points, which may be controlled or, for example, be identified by tactile paving, a crossing island or a dropped kerb. An element of judgement may be required, in which case justification should be provided. Measurement Distances could be measured, for example, along a pavement, across a road at a safe crossing point and along the pavement on the other side. The distance should not be measured diagonally across a road, following the most direct route. Evidence from Google Maps or other digital sources may be used to indicate routes and distances, provided that the scale is appropriate and clearly indicated. Verification The assessor’s site inspection is an important aspect of the assessment of this issue as it must confirm that all relevant information is current and should include photographs of any key areas. This may also help to identify safe crossing points or hazards which may not be apparent from a desktop study. For BREEAM NC and RFO assessments, Google Streetview may be acceptable as evidence to demonstrate safe pedestrian routes and the presence of key features or amenities at Design Stage only. Such information must be verified as above for Final Certification.

07 Mar 2024 - No changes have been made. This appears as 'updated' due to an administrative error.
11 Jan 2024 - Wording re-structured for clarity
19 Dec 2023 - Applicability to BIU V6 confirmed

Shower with multiple shower heads - KBCN0855

To calculate the water use of a shower with more than one shower head, one of the following should be done:

If all of the shower heads can be turned on at once, the flow rates should be added up.
If the shower heads can only be used one at a time, the highest flow rate should be used

22 Feb 2024 - Applied to BIU, BREEAM NC and RFO standards

Sub-metering technologies – Compliance Principle - KBCN1561

Where it can be demonstrated that alternative sub-metering technologies can meet or exceed the capabilities of systems set out in the BREEAM guidance, subject to approval, these can also be considered compliant. It is the role of the Assessor and the project team to provide evidence and justification in a compliance principle query (see KBCN1555). The following metering standards or technologies are currently recognised as alternatives to pulsed output meters:

M-bus. I.e. systems that comply with the EN 13757 series of standards. Also includes systems complying with the OMS (Open Metering System) standards.

Systems serving <10% overall floor area - other affected issues - KBCN1542

The methodology for Ene 01 states: "Heating / cooling systems can be excluded from the calculation where the heated or cooled area equates to less than 10% of overall floor area." Systems which heat or cool < 10% overall floor area are not assessed in:

Ene 01 Building services.
Ene 05 Cooling.
Ene 06 Heating.

Ene 01, 05 and 06 all feed into the asset energy calculator and so their inputs must be consistent. All other issues relating to these excluded systems are still assessed such as:

Ene 11 Installed controls.
Ene 15 and 16 Monitoring energy issues.
Pol 03 Local air quality.
Pol 04 Global warming potential of refrigerants.

Thermographic survey – Standards for test method - KBCN1578

The appropriate international standard for thermographic surveys is ISO 6781:1983 Thermal insulation – Qualitative detection of thermal irregularities in building envelopes – Infrared method. The following are acceptable alternative standards:

EN 13187:1998 Thermal performance of buildings – Qualitative detection of thermal irregularities in building envelopes – Infrared method

Using water from natural underground sources to offset water consumption - KBCN00094

Water from natural underground sources (for instance aquifer water accessed via boreholes) cannot be used to offset:

NC / RFO: potable water consumption.
IU: utility supplied water consumption.

A significant amount of water used for public consumption is already drawn from aquifers. Private boreholes may be drawing water from the same sources as public utility companies.

27-Mar-2024 - Title and text updated to broaden definition. Scheme applicability updated.

View out – Calculating the glazing to wall ratio - KBCN1506

This should be calculated based on the glazed area of window, expressed as a percentage of the area of the external wall in which the window sits. Where the ceiling height of the room is unusually high, relative to the window height, the wall area can be calculated based on a standard ceiling height for the building type.

Washer dryers - KBCN0699

Where a washer dryer is specified, the water consumption figure for the wash and dry cycle should be used. The drying cycle of a washer dryer is taken into account because it usually uses water during this drying process (e.g. for cooling during the drying cycle) and in some cases, this water usage can be significant.

18-Nov-2022 - Updated to apply to BREEAM In-Use Version 6

Washing machines and dishwashers – Water consumption data - KBCN1571

The water consumption data used to demonstrate compliance may be based on the lowest full wash cycle (i.e. not a pre-wash cycle, for example).

Waste streams – clarification - KBCN1526

Scope The focus of the criteria is on recyclable materials only. Any facilities / spaces for managing recyclable materials must be in addition to spaces / facilities for managing general waste. Definition “Waste streams are flows of specific waste, from its source through to recovery, recycling or disposal. Waste streams can be divided into two broad types:

Streams made of materials (such as metals or plastics).
Streams made of certain products (such as electronic waste or end-of-life vehicles).”

Source For BREEAM, a waste stream is a material / product with its own recycling process. This means each stream needs to be separated from other materials before it can be effectively processed into new materials / products. This separation can happen in the asset, or (in the case of co-mingled waste) after collection from the asset. Residential waste streams In most cases, this is defined by how it will be how be sorted and collected by municipal waste authorities. Where no local guidance exists, the list below may be used as a guide. Recyclable waste streams (answer option C in BREEAM In-Use Residential V6):

Paper and cardboard.
Glass.
Plastics.
Metals.
Wood and wood-based products.
Oils.
Batteries.
Electrical and electronic equipment.

Compostable / recyclable waste streams (answer option D in BREEAM In-Use Residential V6):

Food waste.
Garden waste.

Commercial waste streams Commercial assets will generate specialised waste streams specific to the asset's function. These are typically:

Generated consistently, and in large volumes.
Are specifically separated for recycling.

In these cases, waste streams such as metals, plastics and paper / cardboard may be sub-divided into specialised waste streams where they meet the above. Example scenarios [accordion] [accordion_block title="Scope"] A vehicle repair workshop generates the following waste streams:

Metals.
Paper / cardboard.
Plastics.
Engine oils.
General waste.

The engine oils and general waste cannot be re-processed into other usable materials. Only 3 recyclable waste streams can be considered for BREEAM assessment. [/accordion_block] [accordion_block title="Residential"] The local authority collects co-mingled waste for the asset. This waste mixes together:

Metals.
Paper and cardboard.
Plastics.

This co-mingled waste can be counted as 3 waste streams. [/accordion_block] [accordion_block title="Commercial"] A supermarket consistently generates large quantities of cardboard packaging. This cardboard forms a significant portion of recycable waste generation. It is baled up and collected separately by a specialised waste contractor. In this case, cardboard waste can be considered a separate waste stream from paper. [/accordion_block] [/accordion]

18-Jan-2024 - Clarified list of residential waste streams (separated compostable waste streams and added relevant answer options).

In-Use / BIU International Residential V6 /

Carbon monoxide detection – Combustion appliances located outside - KBCN1586

Clarification – percentage of end uses - KBCN1650

Combined system for heating / cooling and domestic hot water - KBCN0329